Home » Articles and guides M1302L: S-band magnetron and waveguide path

M1302L: S-band magnetron and waveguide path

M1302L is a magnetron of the S-band marine radar transmission unit. It is bought as a specific component of the existing radar: here the waveguide output, electrical configuration and the conditions of operation of the transmitter matter. The RadarStation catalogue has a separate M1302L position with its own image; the neighboring M1302LK remains a different catalog position. In this technical guide, we look at L.

Request a quote
M1302L - photo of our catalog card
M1302L: A photo of his own catalog card. Marking on the image is not readable; configuration and condition of the proposed instance are confirmed separately.

What is the M1302L's problem?

The magnetron forms microwave pulses of the transmitting channel. It does not contain everything a radar needs to observe: the antenna, the receiving tract, the processing, and the mapping are all other parts of the system. Therefore, quotation on the M1302L means delivery of a component, not a new radar or ready-made transmission unit in the assembly.

The practical meaning of such an order is to keep the installed system in its intended configuration. In the preparation of repairs, the shipowner may order a separate magnetron, and the restoration of the transmitter may be entrusted to the service organization. If you want a node in the collection or an exchange block, this is another quotation boundary, which should be called immediately: the price of the part does not describe the cost of such a solution.

Frequency and waveguide path

The current description of Nisshinbo for the M1302L specifies a fixed range of 3040–3060 MHz. Output - waveguide WR284, power supply is summed up by wired terminals. The manufacturer specifies a weight of 2.3 kg and air cooling, including forced. This information characterizes a particular design; it is more useful than one broad designation "magnetron at 3 GHz".

For the buyer, the output of WR284 means that it is a waveguide connection, not an antenna connector for a conventional cable. A photograph of the base and the output part helps to describe the desired product, but does not replace the factory drawing. To coordinate with the service, the installed transmitting unit, its modification and the applicable position of the spare part are important. A single frequency match or an external black case is not enough.

Weight and cooling are also applicable. By ordering a separate part for transfer for repair, the buyer does not automatically receive an air duct, fan, fastener, transition element or packaging to return the removed unit. The necessary accessories are included in the general inventory so that the cost and equipment are clear before shipment.

Mode of pulses refers to the entire transmitter

The factory sheet DS-M1302L/M5020 04E sets a maximum pulse duration of 1 μs and a filling factor of 0.001. It separately specifies the conditions of heater and anode power supply, as well as the test current for the characteristics. Limit values cannot be considered a set of simultaneously available operating modes. This data is for the verification of applicability by a specialist, and not instructions for setting up a radar.

This separation is especially important when buying ZIP in advance. The new component itself does not confirm the modulator or cooling state of the current transmitter. If the service orders the magnetron after diagnosis, it is useful to transfer its conclusion along with the application. Then the quotation can be prepared for a known configuration, without promising to restore the detection range with a single replacement of the part.

The M1302L has power descriptions of 25 and 30 kW. The meaning of these numbers is already discussed in our article on M1555, M1302A and M1302L (/st/m1555-m1302a-m1302l-moshchnost-pasport.html). Here is fundamentally different: the choice of L can not be reduced to one power, leaving without attention the output and mode of the transmitting unit.

Designation M5020 and neighboring models

The official document combines the designation M1302L/M5020. This allows you to accurately name the source of the characteristics, but does not give grounds to promise any delivery with a similar number as an agreed replacement. If the quotation specifies M5020, the manufacturer and marking of the proposed part must be known and the applicability to the specific equipment must be confirmed prior to order.

For M1302A, M1302LK, and other related indices, the description of L cannot be transferred by external similarity. In the application, it is better to leave the full type of installed product and the number from the radar documentation. In case of divergence of designations, the proposed configuration is agreed upon; silent replacement of the letter in the account does not solve the issue of compatibility.

What is included in the quotation

In its own card, the M1302L is presented in the catalog and has a warehouse mark. This is a reference point for a separate component; current price, balance, manufacturer, condition and term are confirmed by quotation. Catalogue photography helps to find out the design, and the actual marking and completeness are checked for the proposed product.

Specify the number, radar model, transmitting unit and city or port of receipt. If accessories, documents, inspection or work are required, list them together: a common price is required for an agreed set, with a separate designation of service works. Delivery to the regions of Russia and Kazakhstan is coordinated at the address and the required date, without the promise of the same period for all destinations.

M1302L in our catalogue

M1302LM1302L - Magnetron S-band.

The current price is indicated in the product card. for the required set, the total price is indicated.

Request a quote

Primary source: Nisshinbo: M1302L, frequency, interfaces and design · Nisshinbo DS-M1302L/M5020, Rev. 04E from 27.10.2022.

All technical guide RadarStation