MG5241F: transmitter component and scope of supply
The MG5241F is used to restore an existing marine radar transmitter when it is necessary to maintain the agreed type of magnetron and its mechanical configuration. In RadarStation there is a separate card of this model with a guide see the product card. Below is what is the component of the usefulness of a full datasheet and how to coordinate the delivery without replacing a specific part with an abstract “X-band magnetron”.
Request a quote
What is the purpose of the MG5241F?
It is a fixed frequency pulse magnetron with a built-in magnet. The Marconi Applied Technologies archival factory datasheet has an operating frequency of 9410 ± 30 MHz. The component forms microwave pulses as part of the transmitting node; it does not replace the entire transceiver, antenna system, or radar processor. The buyer needs an applicable spare component, and not an independent means of detecting targets.
Hence the practical boundary of the order. If the service statement indicates MG5241F, the quotation should keep this designation in its entirety. You can’t choose a product just by the phrase “9.4 GHz”: it describes a range of different parts. On the other hand, the coincidence of the marking does not establish the cause of the radar malfunction. The decision to replace is based on the conclusion of service of a particular transmitter.
Configuration F and the place in the transmitting unit
The factory document compares the MG5241F to the MG5241 and specifically notes the ability to use all six mounting holes. This is a meaningful configuration difference, which is easy to lose in a shortened application without the last letter. The presence of six holes does not mean that each transmitter necessarily uses all six: the actual mounting scheme is determined by the documentation of the equipment.
The model has a waveguide output and IEC UBR100 connection, cooling is natural. The built-in magnet, base, output and terminals form a specific design. A similar flange or matching size of one section does not prove the interchangeability of the whole product. To order, you need a photo of the installed marking and the designation of the transmitting unit; installation features are verified by the service organization according to the drawings, without independently altering the base.
datasheet describes several levels of data
In the document A1A-MG5241F, Issue 4 for October 2001, the typical modes, limit values and individual conditions of factory tests are given. These sections perform different tasks. The typical mode helps to understand the nature of the component, limits set limits, and results under given conditions refer to these conditions. You can’t mix them into one shortened specification line.
For example, a typical peak power of 10 kW is given for this edition. This is a characteristic of the pulse component in the described mode, not the consumption of a marine post or the promise of a certain detection range. An increase in the number on someone else’s price list does not make another type an improved replacement. For acceptance, the applicable factory document, specific configuration and compliance with the agreed position are important.
The archived date of the datasheet also does not determine the age of the proposed copy. It does not confirm either fresh release or long-term storage. Manufacturer, actual marking, condition, available documents and lot details shall relate to the product included in the quotation. The e2v name on our card does not override this verification and does not turn the Marconi archival document into a datasheet of a specific shipment.
What to buy with the detail
The appropriate composition depends on the task: only the confirmed MG5241F in the current zip or the delivery of a component with separately agreed accessories and service. Transition plate, fasteners, seals, operations and radar checks do not become switched on automatically. If they are needed, the quotation requires a full composition and a total price so that the buyer does not compare the cost of one magnetron with the price of the completed recovery.
The general order of reading Gen4 tables with transition plates has already been disassembled separately; it is not necessary to repeat these tables here. For the purchase of the MG5241F itself, start with the established type and applicable statement. Service conclusion, photo nameplate of the transmitter and the list of required accessories will allow you to form a certain delivery, preserving the difference between the price of the part and the price of work.
Request for delivery to the place of service
Specify the number, city, point of receipt and the desired date. It is useful for a ship to name the place of transfer of the service organization: delivery to the office and transfer to the place of work can be different routes. For Moscow, St. Petersburg, Novosibirsk and other cities of Russia or Kazakhstan, a specific shipment is agreed; the term and cost of transportation are confirmed by the quotation. Availability on the card is checked when responding to the application, before payment and planning of work.
If some of the original data is unknown, leave it explicitly in the letter. We will be able to request the missing marking and agree on the exact position. The commercial result is a clear scope of supply MG5241F with price, documents and deadline; installation and configuration are performed according to the documentation of a specific radar.
MG5241F in our catalogue
The current price is indicated in the product card. for the required set, the total price is indicated.
Request a quotePrimary source: Marconi Applied Technologies: MG5241F, A1A-MG5241F Issue 4, October 2001.
Reading Gen4 tables and transition plates · All technical guide RadarStation