Spare parts for two different radars on one vessel
The ship has two different radars, and the supply wants to order one set of ZIP for them. Two magnetrons appear in the application, but the number itself does not yet show whether both installations are provided with a reserve. Let’s consider the conditional case where the technical service confirmed the M1623 for one transmitter and the M1636 for another: how to keep this assignment when agreeing on a common order.
Request a quote
Two magnetrons can only close one installation.
Let's say the old stock is in the same place. M1636. When planning a purchase, they offer to take another one: you will get two spare positions, and the total amount of the order looks sufficient. However, for the second transmitter in our example, the M1623. Additional M1636 increases the supply for the first installation, and the need for the second remains open. This can only be seen if you look at each radar separately.
Therefore, the useful result of the purchase is formulated through the appointment: an agreed position for the transmitter of the first radar and an agreed position for the transmitter of the second. The number of each type is selected according to the conditions of the operator and service. One position of each designation here is an example of a kit structure, not a universal reserve rate for any vessel.
What really confirms the factory catalog
Nisshinbo classifies the M1623 as an S-band magnetron with a peak power output of 30 kW, and the M1636 as an X-band with a peak power of 25 kW. These are two different products for different ranges. The difference helps to understand why they can’t be reduced to a single universal warehouse position, even when the purchase is combined into one order.
X-band and S-band do not choose a magnetron instead of a specific transmitter. There are different products within each range. In our example, the M1623/M1636 pair appears in the quotation after validation of applicability to two installed transmitters. For another vessel, the correct pair may be different; the appearance of the parts and the display make of this solution do not determine.
One marine set - two precise destinations
Start the discussion with two installed transmission units. Each requires a manufacturer, model, serial number and available information about the actually installed component. If the display and the transmitter have different designations, both are retained, without substituting the transmitter name for the system on the bridge. The Technical Service shall add the applicable documentation and a confirmed list of spare parts.
After this comparison, the quotation can be collected in its entirety. It retains the connection of each supplied position with its installation: which magnetron is designed for the first radar, which is for the second, what configuration and number are agreed. Required accessories include confirmed composition. Their presence cannot be inferred from a photograph of a single magnetron or automatically considered the same for both transmitters.
This is convenient for both the buyer and the service provider. Supply gets one agreed-upon cost of the kit, and the technical service sees two different uses inside it. If only one item changes during clarification, it is clear which installation the change belongs to and which part of the order still needs to be agreed upon. The second position is not a substitute for it.
How to discuss incomplete quotation
Assume the confirmed M1623 is available for approval, and the M1636 still requires a configuration or deadline. It is useful to point out at once that the quotation covers only one part of the requirement. You can discuss the overall delivery or agreed individual stages, maintaining the composition of the entire order. This is a commercial decision to obtain a PPI; the admissibility of operating marine equipment is determined by separately responsible specialists.
Another case – the service specified the designation of the component of the second radar. Then they review this part of the kit, and not pick up any position of similar power instead. The order remains tied to two specific installations. Shared packaging, one bill, or the same manufacturer alone do not create interchangeability of parts and do not confirm the readiness of both systems to work.
The presence of two spare magnetrons is also not a redundancy of the entire radar system. Stock refers to the agreed components; it does not eliminate the faults of other nodes and does not confirm their condition. Work and subsequent inspection of equipment are planned with qualified service. At the purchase stage, it is important to get the right composition, without attributing the properties of the completed repair or the second operating radar to the set.
What to send for general calculation
Send the data of both radars and transmitters, their serial numbers, component markings and supporting documents. Separately indicate the existing stock: this will help distinguish the purchase of a missing position from an increase in the amount of the same type. Add the required number, place of receipt, desired date, organization and contact of the technical responsible.
Ask to calculate the complete agreed set with the total price and clear purpose of its parts. If the applicability of one position is still being checked, mark it directly in the request. For delivery in Russia or Kazakhstan, specify the city and address: quotation composition, actual availability, documents and deadline are confirmed for a specific delivery.

On approval of the kit
Can I order both positions in one set?
Yes, request a general calculation for two specific installations. Designations, configuration, quantity and accessories are agreed separately for each part, after which the composition and total cost of the set are recorded.
The two M1636s replace the M1623 and M1636 sets.
In this case, they will increase the position reserve for one confirmed transmitter. Applicability to another transmitter does not arise from quantity; it requires its own confirmed position.
The main items of the kit in our catalog
M1623 - S-band magnetron
For the M1623 reference card, see the product card.
Request a quoteM1636 - X-band magnetron
For the M1636 card reference, see the product card.
Request a quoteFull agreed set - upon request. Prices of individual cards are not quotation of a ready-made compatible set. Assignment for each transmitter, configuration, quantity, accessories, condition, actual availability, documents and total cost are confirmed by quotation.
Request a quotePrimary sources: Nisshinbo — M1623, S-band 30 kW · Nisshinbo — M1636, X-band 25 kW. Manufacturer's documents confirm the product parameters; applicability to specific transmitters is agreed separately.